Optimizing Laser Sintering Parameters and Cooling Channel Designs for Enhanced Injection Molding of Medical Tube Connectors

Ding Yang  Hsu

doi:10.6180/jase.202511_28(11).0009

Optimizing Laser Sintering Parameters and Cooling Channel Designs for Enhanced Injection Molding of Medical Tube Connectors

Research Categories

Ding Yang HsuThis email address is being protected from spambots. You need JavaScript enabled to view it.

Department of Industrial Design, Ming-Chi University of Technology, New Taipei City, Taiwan, R.O.C.

Received: December 31, 2024
Accepted: February 1, 2025
Publication Date: March 15, 2025

Copyright The Author(s). This is an open access article distributed under the terms of the Creative Commons Attribution License (CC BY 4.0), which permits unrestricted use, distribution, and reproduction in any medium, provided the original author and source are cited.

Download Citation: ||https://doi.org/10.6180/jase.202511_28(11).0009

Respiratory equipment disconnections in hospitals pose severe risks, including hypoxia and mortality. Subop timal tube connector quality, often worsened by traditional cooling mold designs, results in uneven thermal equilibrium, product deformation, and higher defect rates. This study focuses on optimizing laser sintering parameters and cooling channel designs to enhance the injection molding process for medical tube connectors. Using the Taguchi method with an L9 (3⁴) orthogonal array, the effects of laser power, layer thickness, hatch spacing, and scanning speed on sintering quality were evaluated. Laser power emerged as the most influential factor, contributing 83.09% to sintering quality, followed by scanning speed (9.48%), layer thickness (5.81%), and hatch spacing (1.61%). The optimal parameters- 100% laser power, 40µ m layer thickness, 0.06 mm hatch spacing, and 200 mm/s scanning speed-produced mold cores with minimal pores, enhanced structural integrity, and consistent quality. Injection molding trials compared conformal cooling, traditional cooling, and no-cooling designs. Conformal cooling reduced cycle times by 15 seconds ( 33.1 vs. 48.1 seconds) and improved taper accuracy from 0.57 mm to 0.89 mm , reducing dimensional defects by 40%. Both cooling designs met ISO-5356 standards for length, but conformal cooling achieved higher stability and accuracy, aligning closely with the ideal taper of 2.2 mm . Molds without cooling channels exhibited significantly longer cycle times and higher defect rates, underscoring the importance of effective cooling systems in precision manufacturing. This study confirms the advantages of conformal cooling for enhancing injection molding efficiency and product quality in medical device production. Future research should explore alternative cooling geometries and computational simulations. Keywords: Laser Sintering Optimization, Conformal Cooling Channels, Medical Tube Connectors, Injection Molding, ISO-5356 Compliance

Keywords: Laser Sintering Optimization; Conformal Cooling Channels; Medical Tube Connectors; Injection Molding; ISO-5356 Compliance

[1] Ministry of Health and Welfare. 2017 Annual Report on Taiwan Patient Safety Report System (Raw Data). Tech. rep. [Online]. Ministry of Health and Welfare, Taiwan, 2018.
[2] International Organization for Standardization. ISO 5356-1:2004- Anaesthetic and Respiratory Equipment — Conical Connectors. 2004.
[3] H. M. Silva, J. T. Noversa, L. Fernandes, H. L. Ro drigues, and A. J. Pontes, (2022) “Design, Simulation and Optimization of Conformal Cooling Channels in In jection Molds: A Review" The International Journal of Advanced Manufacturing Technology 120: 4291 4305. DOI: 10.1007/s00170-022-08693-4.
[4] H.-S. Park and X.-P. Dang, (2017) “Development of a Smart Plastic Injection Mold with Conformal Cooling Channels" Procedia Manufacturing 10: 48–59. DOI: 10.1016/j.promfg.2017.07.020.
[5] Ministry of Health and Welfare. Article 4 Annex II of the Regulations for Governing the Management of Medical Devices. Tech. rep. [Online]. Ministry of Health and Welfare, Taiwan, 2017.
[6] S. Kitayama, K. Tamada, M. Takano, and S. Aiba, (2018) “Numerical Optimization of Process Parameters in Plastic Injection Molding for Minimizing Weld Lines and Clamping Force Using the Conformal Cooling Chan nel" Journal of Manufacturing Processes 32: 782–790. DOI: 10.1016/j.jmapro.2018.04.007.
[7] L. Q. Tang, C. Chassapis, and S. Manoochehri, (2022) “Dynamic Conformal Cooling Improves Injection Molding: Hybrid Molds Manufactured by Laser Powder Bed Fusion" The International Journal of Advanced Manufactur ing Technology 120: 4291–4305. DOI: 10.1007/s00170 021-06794-0.
[8] W.E.Frazier, (2014) “Metal Additive Manufacturing: A Review" Journal of Materials Engineering and Per formance 23(6): 1917–1928. DOI: 10.1007/s11665-014 0958-z.
[9] J. Lin. “3D Metal Powder Printing Sintering Parameter Studies". [Online]. (Master’s thesis). National Taiwan University, Taiwan, 2017.